For the past many years, there have been many forms of the game of pool in existence. The fact that there have been various changes to the materials that the game is comprised has not had an effect on the felt cover. It is one aspect that has remained the same over time. However, it has a short lifetime that means it has to be replaced over and over after some time. In consideration of pool table refelting Denver residents should be acquainted with the basic of the procedure.
Among the materials required for the replacement are a socket wrench, felts, rag, cleanser, staple gun and hammer. For a start, the staples surrounding the pockets towards the underside of the table will need to be removed. This is followed by removing the rails securing the underside through the use of a socket wrench. Approximately, the individual will need to locate three bolts for every rail.
After all the bolts have been removed, the rails will need to be taken off. This will be followed by detaching of the pocket liners. The staples that attach the felt to rail cushions will have to be pulled out. Felt covering the cushions will then need to be removed, after which it gets removed from the table top. At this stage, one has to determine if the felt gets glued or stapled, or both. The staples that are hold the felt are removed using a staple puller. Removal of the glued felt is supposed to be done very gently.
The next step is the preparation of the slate so that it is re-felted. All the cracks and holes are filled using pool table waxes. The wax will need to be left to harden for a minute or so. Any excesses are scrapped with a putty knife. It will then be important to clean the slate surface using a gentle cleanser. The surface has to dry completely before it is covered.
The felt pieces that are being used will need to be measured. This will ensure that they are cut in accordance to the dimensions of the table. Edges of the felt are aligned flush with the table edges. As a matter of fact, the measurements should be very accurately done so that it fits well to the table.
The next process is normally very important. One will need to start stapling the fabric to the table. The process is started at the center of one short edge before proceeding to the corners. All this is done while remembering not to cover the pockets. When placing the staples, one needs to move in increments of about two inches while pulling the fabric taut. This is done for all the sides of the table.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
There is wrapping of the rails with felt. It would be vital to observe the unique design of the rails so as to determine the size of felt pieces to use. The rails are attached to the table, and then the liners and pockets are replaced accordingly.
Among the materials required for the replacement are a socket wrench, felts, rag, cleanser, staple gun and hammer. For a start, the staples surrounding the pockets towards the underside of the table will need to be removed. This is followed by removing the rails securing the underside through the use of a socket wrench. Approximately, the individual will need to locate three bolts for every rail.
After all the bolts have been removed, the rails will need to be taken off. This will be followed by detaching of the pocket liners. The staples that attach the felt to rail cushions will have to be pulled out. Felt covering the cushions will then need to be removed, after which it gets removed from the table top. At this stage, one has to determine if the felt gets glued or stapled, or both. The staples that are hold the felt are removed using a staple puller. Removal of the glued felt is supposed to be done very gently.
The next step is the preparation of the slate so that it is re-felted. All the cracks and holes are filled using pool table waxes. The wax will need to be left to harden for a minute or so. Any excesses are scrapped with a putty knife. It will then be important to clean the slate surface using a gentle cleanser. The surface has to dry completely before it is covered.
The felt pieces that are being used will need to be measured. This will ensure that they are cut in accordance to the dimensions of the table. Edges of the felt are aligned flush with the table edges. As a matter of fact, the measurements should be very accurately done so that it fits well to the table.
The next process is normally very important. One will need to start stapling the fabric to the table. The process is started at the center of one short edge before proceeding to the corners. All this is done while remembering not to cover the pockets. When placing the staples, one needs to move in increments of about two inches while pulling the fabric taut. This is done for all the sides of the table.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
There is wrapping of the rails with felt. It would be vital to observe the unique design of the rails so as to determine the size of felt pieces to use. The rails are attached to the table, and then the liners and pockets are replaced accordingly.
About the Author:
You can visit www.anytimebilliards.com for more helpful information about Steps Of Pool Table Refelting Denver.
No comments:
Post a Comment